source: trunk/minix/drivers/dp8390/dp8390.h@ 10

Last change on this file since 10 was 9, checked in by Mattia Monga, 14 years ago

Minix 3.1.2a
File size: 11.8 KB
Line 
1/*
2dp8390.h
3
4Created: before Dec 28, 1992 by Philip Homburg
5*/
6
7/* National Semiconductor DP8390 Network Interface Controller. */
8
9 /* Page 0, for reading ------------- */
10#define DP_CR 0x0 /* Read side of Command Register */
11#define DP_CLDA0 0x1 /* Current Local Dma Address 0 */
12#define DP_CLDA1 0x2 /* Current Local Dma Address 1 */
13#define DP_BNRY 0x3 /* Boundary Pointer */
14#define DP_TSR 0x4 /* Transmit Status Register */
15#define DP_NCR 0x5 /* Number of Collisions Register */
16#define DP_FIFO 0x6 /* Fifo ?? */
17#define DP_ISR 0x7 /* Interrupt Status Register */
18#define DP_CRDA0 0x8 /* Current Remote Dma Address 0 */
19#define DP_CRDA1 0x9 /* Current Remote Dma Address 1 */
20#define DP_DUM1 0xA /* unused */
21#define DP_DUM2 0xB /* unused */
22#define DP_RSR 0xC /* Receive Status Register */
23#define DP_CNTR0 0xD /* Tally Counter 0 */
24#define DP_CNTR1 0xE /* Tally Counter 1 */
25#define DP_CNTR2 0xF /* Tally Counter 2 */
26
27 /* Page 0, for writing ------------- */
28#define DP_CR 0x0 /* Write side of Command Register */
29#define DP_PSTART 0x1 /* Page Start Register */
30#define DP_PSTOP 0x2 /* Page Stop Register */
31#define DP_BNRY 0x3 /* Boundary Pointer */
32#define DP_TPSR 0x4 /* Transmit Page Start Register */
33#define DP_TBCR0 0x5 /* Transmit Byte Count Register 0 */
34#define DP_TBCR1 0x6 /* Transmit Byte Count Register 1 */
35#define DP_ISR 0x7 /* Interrupt Status Register */
36#define DP_RSAR0 0x8 /* Remote Start Address Register 0 */
37#define DP_RSAR1 0x9 /* Remote Start Address Register 1 */
38#define DP_RBCR0 0xA /* Remote Byte Count Register 0 */
39#define DP_RBCR1 0xB /* Remote Byte Count Register 1 */
40#define DP_RCR 0xC /* Receive Configuration Register */
41#define DP_TCR 0xD /* Transmit Configuration Register */
42#define DP_DCR 0xE /* Data Configuration Register */
43#define DP_IMR 0xF /* Interrupt Mask Register */
44
45 /* Page 1, read/write -------------- */
46#define DP_CR 0x0 /* Command Register */
47#define DP_PAR0 0x1 /* Physical Address Register 0 */
48#define DP_PAR1 0x2 /* Physical Address Register 1 */
49#define DP_PAR2 0x3 /* Physical Address Register 2 */
50#define DP_PAR3 0x4 /* Physical Address Register 3 */
51#define DP_PAR4 0x5 /* Physical Address Register 4 */
52#define DP_PAR5 0x6 /* Physical Address Register 5 */
53#define DP_CURR 0x7 /* Current Page Register */
54#define DP_MAR0 0x8 /* Multicast Address Register 0 */
55#define DP_MAR1 0x9 /* Multicast Address Register 1 */
56#define DP_MAR2 0xA /* Multicast Address Register 2 */
57#define DP_MAR3 0xB /* Multicast Address Register 3 */
58#define DP_MAR4 0xC /* Multicast Address Register 4 */
59#define DP_MAR5 0xD /* Multicast Address Register 5 */
60#define DP_MAR6 0xE /* Multicast Address Register 6 */
61#define DP_MAR7 0xF /* Multicast Address Register 7 */
62
63/* Bits in dp_cr */
64#define CR_STP 0x01 /* Stop: software reset */
65#define CR_STA 0x02 /* Start: activate NIC */
66#define CR_TXP 0x04 /* Transmit Packet */
67#define CR_DMA 0x38 /* Mask for DMA control */
68#define CR_DM_NOP 0x00 /* DMA: No Operation */
69#define CR_DM_RR 0x08 /* DMA: Remote Read */
70#define CR_DM_RW 0x10 /* DMA: Remote Write */
71#define CR_DM_SP 0x18 /* DMA: Send Packet */
72#define CR_DM_ABORT 0x20 /* DMA: Abort Remote DMA Operation */
73#define CR_PS 0xC0 /* Mask for Page Select */
74#define CR_PS_P0 0x00 /* Register Page 0 */
75#define CR_PS_P1 0x40 /* Register Page 1 */
76#define CR_PS_P2 0x80 /* Register Page 2 */
77#define CR_PS_T1 0xC0 /* Test Mode Register Map */
78
79/* Bits in dp_isr */
80#define ISR_PRX 0x01 /* Packet Received with no errors */
81#define ISR_PTX 0x02 /* Packet Transmitted with no errors */
82#define ISR_RXE 0x04 /* Receive Error */
83#define ISR_TXE 0x08 /* Transmit Error */
84#define ISR_OVW 0x10 /* Overwrite Warning */
85#define ISR_CNT 0x20 /* Counter Overflow */
86#define ISR_RDC 0x40 /* Remote DMA Complete */
87#define ISR_RST 0x80 /* Reset Status */
88
89/* Bits in dp_imr */
90#define IMR_PRXE 0x01 /* Packet Received iEnable */
91#define IMR_PTXE 0x02 /* Packet Transmitted iEnable */
92#define IMR_RXEE 0x04 /* Receive Error iEnable */
93#define IMR_TXEE 0x08 /* Transmit Error iEnable */
94#define IMR_OVWE 0x10 /* Overwrite Warning iEnable */
95#define IMR_CNTE 0x20 /* Counter Overflow iEnable */
96#define IMR_RDCE 0x40 /* DMA Complete iEnable */
97
98/* Bits in dp_dcr */
99#define DCR_WTS 0x01 /* Word Transfer Select */
100#define DCR_BYTEWIDE 0x00 /* WTS: byte wide transfers */
101#define DCR_WORDWIDE 0x01 /* WTS: word wide transfers */
102#define DCR_BOS 0x02 /* Byte Order Select */
103#define DCR_LTLENDIAN 0x00 /* BOS: Little Endian */
104#define DCR_BIGENDIAN 0x02 /* BOS: Big Endian */
105#define DCR_LAS 0x04 /* Long Address Select */
106#define DCR_BMS 0x08 /* Burst Mode Select
107 * Called Loopback Select (LS) in
108 * later manuals. Should be set. */
109#define DCR_AR 0x10 /* Autoinitialize Remote */
110#define DCR_FTS 0x60 /* Fifo Threshold Select */
111#define DCR_2BYTES 0x00 /* 2 bytes */
112#define DCR_4BYTES 0x40 /* 4 bytes */
113#define DCR_8BYTES 0x20 /* 8 bytes */
114#define DCR_12BYTES 0x60 /* 12 bytes */
115
116/* Bits in dp_tcr */
117#define TCR_CRC 0x01 /* Inhibit CRC */
118#define TCR_ELC 0x06 /* Encoded Loopback Control */
119#define TCR_NORMAL 0x00 /* ELC: Normal Operation */
120#define TCR_INTERNAL 0x02 /* ELC: Internal Loopback */
121#define TCR_0EXTERNAL 0x04 /* ELC: External Loopback LPBK=0 */
122#define TCR_1EXTERNAL 0x06 /* ELC: External Loopback LPBK=1 */
123#define TCR_ATD 0x08 /* Auto Transmit Disable */
124#define TCR_OFST 0x10 /* Collision Offset Enable (be nice) */
125
126/* Bits in dp_tsr */
127#define TSR_PTX 0x01 /* Packet Transmitted (without error)*/
128#define TSR_DFR 0x02 /* Transmit Deferred, reserved in
129 * later manuals. */
130#define TSR_COL 0x04 /* Transmit Collided */
131#define TSR_ABT 0x08 /* Transmit Aborted */
132#define TSR_CRS 0x10 /* Carrier Sense Lost */
133#define TSR_FU 0x20 /* FIFO Underrun */
134#define TSR_CDH 0x40 /* CD Heartbeat */
135#define TSR_OWC 0x80 /* Out of Window Collision */
136
137/* Bits in tp_rcr */
138#define RCR_SEP 0x01 /* Save Errored Packets */
139#define RCR_AR 0x02 /* Accept Runt Packets */
140#define RCR_AB 0x04 /* Accept Broadcast */
141#define RCR_AM 0x08 /* Accept Multicast */
142#define RCR_PRO 0x10 /* Physical Promiscuous */
143#define RCR_MON 0x20 /* Monitor Mode */
144
145/* Bits in dp_rsr */
146#define RSR_PRX 0x01 /* Packet Received Intact */
147#define RSR_CRC 0x02 /* CRC Error */
148#define RSR_FAE 0x04 /* Frame Alignment Error */
149#define RSR_FO 0x08 /* FIFO Overrun */
150#define RSR_MPA 0x10 /* Missed Packet */
151#define RSR_PHY 0x20 /* Multicast Address Match */
152#define RSR_DIS 0x40 /* Receiver Disabled */
153#define RSR_DFR 0x80 /* In later manuals: Deferring */
154
155typedef struct dp_rcvhdr
156{
157 u8_t dr_status; /* Copy of rsr */
158 u8_t dr_next; /* Pointer to next packet */
159 u8_t dr_rbcl; /* Receive Byte Count Low */
160 u8_t dr_rbch; /* Receive Byte Count High */
161} dp_rcvhdr_t;
162
163#define DP_PAGESIZE 256
164
165/* Some macros to simplify accessing the dp8390 */
166#define inb_reg0(dep, reg) (inb(dep->de_dp8390_port+reg))
167#define outb_reg0(dep, reg, data) (outb(dep->de_dp8390_port+reg, data))
168#define inb_reg1(dep, reg) (inb(dep->de_dp8390_port+reg))
169#define outb_reg1(dep, reg, data) (outb(dep->de_dp8390_port+reg, data))
170
171/* Software interface to the dp8390 driver */
172
173struct dpeth;
174struct iovec_dat;
175_PROTOTYPE( typedef void (*dp_initf_t), (struct dpeth *dep) );
176_PROTOTYPE( typedef void (*dp_stopf_t), (struct dpeth *dep) );
177_PROTOTYPE( typedef void (*dp_user2nicf_t), (struct dpeth *dep,
178 struct iovec_dat *iovp, vir_bytes offset,
179 int nic_addr, vir_bytes count) );
180_PROTOTYPE( typedef void (*dp_nic2userf_t), (struct dpeth *dep,
181 int nic_addr, struct iovec_dat *iovp,
182 vir_bytes offset, vir_bytes count) );
183#if 0
184_PROTOTYPE( typedef void (*dp_getheaderf_t), (struct dpeth *dep,
185 int page, struct dp_rcvhdr *h, u16_t *eth_type) );
186#endif
187_PROTOTYPE( typedef void (*dp_getblock_t), (struct dpeth *dep,
188 int page, size_t offset, size_t size, void *dst) );
189
190/* iovectors are handled IOVEC_NR entries at a time. */
191#define IOVEC_NR 16
192
193typedef int irq_hook_t;
194
195typedef struct iovec_dat
196{
197 iovec_t iod_iovec[IOVEC_NR];
198 int iod_iovec_s;
199 int iod_proc_nr;
200 vir_bytes iod_iovec_addr;
201} iovec_dat_t;
202
203#define SENDQ_NR 2 /* Maximum size of the send queue */
204#define SENDQ_PAGES 6 /* 6 * DP_PAGESIZE >= 1514 bytes */
205
206typedef struct dpeth
207{
208 /* The de_base_port field is the starting point of the probe.
209 * The conf routine also fills de_linmem and de_irq. If the probe
210 * routine knows the irq and/or memory address because they are
211 * hardwired in the board, the probe should modify these fields.
212 * Futhermore, the probe routine should also fill in de_initf and
213 * de_stopf fields with the appropriate function pointers and set
214 * de_prog_IO iff programmed I/O is to be used.
215 */
216 port_t de_base_port;
217 phys_bytes de_linmem;
218 int de_irq;
219 int de_int_pending;
220 irq_hook_t de_hook;
221 dp_initf_t de_initf;
222 dp_stopf_t de_stopf;
223 int de_prog_IO;
224 char de_name[sizeof("dp8390#n")];
225
226 /* The initf function fills the following fields. Only cards that do
227 * programmed I/O fill in the de_pata_port field.
228 * In addition, the init routine has to fill in the sendq data
229 * structures.
230 */
231 ether_addr_t de_address;
232 port_t de_dp8390_port;
233 port_t de_data_port;
234 int de_16bit;
235 int de_ramsize;
236 int de_offset_page;
237 int de_startpage;
238 int de_stoppage;
239
240#if ENABLE_PCI
241 /* PCI config */
242 char de_pci; /* TRUE iff PCI device */
243 u8_t de_pcibus;
244 u8_t de_pcidev;
245 u8_t de_pcifunc;
246#endif
247
248 /* Do it yourself send queue */
249 struct sendq
250 {
251 int sq_filled; /* this buffer contains a packet */
252 int sq_size; /* with this size */
253 int sq_sendpage; /* starting page of the buffer */
254 } de_sendq[SENDQ_NR];
255 int de_sendq_nr;
256 int de_sendq_head; /* Enqueue at the head */
257 int de_sendq_tail; /* Dequeue at the tail */
258
259 /* Fields for internal use by the dp8390 driver. */
260 int de_flags;
261 int de_mode;
262 eth_stat_t de_stat;
263 iovec_dat_t de_read_iovec;
264 iovec_dat_t de_write_iovec;
265 iovec_dat_t de_tmp_iovec;
266 vir_bytes de_read_s;
267 int de_client;
268 message de_sendmsg;
269 dp_user2nicf_t de_user2nicf;
270 dp_nic2userf_t de_nic2userf;
271 dp_getblock_t de_getblockf;
272} dpeth_t;
273
274#define DEI_DEFAULT 0x8000
275
276#define DEF_EMPTY 0x000
277#define DEF_PACK_SEND 0x001
278#define DEF_PACK_RECV 0x002
279#define DEF_SEND_AVAIL 0x004
280#define DEF_READING 0x010
281#define DEF_PROMISC 0x040
282#define DEF_MULTI 0x080
283#define DEF_BROAD 0x100
284#define DEF_ENABLED 0x200
285#define DEF_STOPPED 0x400
286
287#define DEM_DISABLED 0x0
288#define DEM_SINK 0x1
289#define DEM_ENABLED 0x2
290
291#if !__minix_vmd
292#define debug 0 /* Standard Minix lacks debug variable */
293#endif
294
295/*
296 * $PchId: dp8390.h,v 1.10 2005/02/10 17:26:06 philip Exp $
297 */
Note: See TracBrowser for help on using the repository browser.