source: trunk/minix/drivers/dp8390/wdeth.h@ 20

Last change on this file since 20 was 9, checked in by Mattia Monga, 14 years ago

Minix 3.1.2a

File size: 3.2 KB
Line 
1/*
2wdeth.h
3
4Created: before Dec 28, 1992 by Philip Homburg
5*/
6
7#ifndef WDETH_H
8#define WDETH_H
9
10/* Western Digital Ethercard Plus, or WD8003E card. */
11
12#define EPL_REG0 0x0 /* Control(write) and status(read) */
13#define EPL_REG1 0x1
14#define EPL_REG2 0x2
15#define EPL_REG3 0x3
16#define EPL_REG4 0x4
17#define EPL_REG5 0x5
18#define EPL_REG6 0x6
19#define EPL_REG7 0x7
20#define EPL_EA0 0x8 /* Most significant eaddr byte */
21#define EPL_EA1 0x9
22#define EPL_EA2 0xA
23#define EPL_EA3 0xB
24#define EPL_EA4 0xC
25#define EPL_EA5 0xD /* Least significant eaddr byte */
26#define EPL_TLB 0xE
27#define EPL_CHKSUM 0xF /* sum from epl_ea0 upto here is 0xFF */
28#define EPL_DP8390 0x10 /* NatSemi chip */
29
30#define EPL_MSR EPL_REG0 /* memory select register */
31#define EPL_ICR EPL_REG1 /* interface configuration register */
32#define EPL_IRR EPL_REG4 /* interrupt request register (IRR) */
33#define EPL_790_HWR EPL_REG4 /* '790 hardware support register */
34#define EPL_LAAR EPL_REG5 /* LA address register (write only) */
35#define EPL_790_ICR EPL_REG6 /* '790 interrupt control register */
36#define EPL_GP2 EPL_REG7 /* general purpose register 2 */
37#define EPL_790_B EPL_EA3 /* '790 memory register */
38#define EPL_790_GCR EPL_EA5 /* '790 General Control Register */
39
40/* Bits in EPL_MSR */
41#define E_MSR_MEMADDR 0x3F /* Bits SA18-SA13, SA19 implicit 1 */
42#define E_MSR_MENABLE 0x40 /* Memory Enable */
43#define E_MSR_RESET 0x80 /* Software Reset */
44
45/* Bits in EPL_ICR */
46#define E_ICR_16BIT 0x01 /* 16 bit bus */
47#define E_ICR_IR2 0x04 /* bit 2 of encoded IRQ */
48#define E_ICR_MEMBIT 0x08 /* 583 mem size mask */
49
50/* Bits in EPL_IRR */
51#define E_IRR_IR0 0x20 /* bit 0 of encoded IRQ */
52#define E_IRR_IR1 0x40 /* bit 1 of encoded IRQ */
53#define E_IRR_IEN 0x80 /* enable interrupts */
54
55/* Bits in EPL_LAAR */
56#define E_LAAR_A19 0x01 /* address lines for above 1M ram */
57#define E_LAAR_A20 0x02 /* address lines for above 1M ram */
58#define E_LAAR_A21 0x04 /* address lines for above 1M ram */
59#define E_LAAR_A22 0x08 /* address lines for above 1M ram */
60#define E_LAAR_A23 0x10 /* address lines for above 1M ram */
61#define E_LAAR_SOFTINT 0x20 /* enable software interrupt */
62#define E_LAAR_LAN16E 0x40 /* enables 16 bit RAM for LAN */
63#define E_LAAR_MEM16E 0x80 /* enables 16 bit RAM for host */
64
65/* Bits and values in EPL_TLB */
66#define E_TLB_EB 0x05 /* WD8013EB */
67#define E_TLB_E 0x27 /* WD8013 Elite */
68#define E_TLB_SMCE 0x29 /* SMC Elite 16 */
69#define E_TLB_SMC8216T 0x2A /* SMC 8216 T */
70#define E_TLB_SMC8216C 0x2B /* SMC 8216 C */
71
72#define E_TLB_REV 0x1F /* revision mask */
73#define E_TLB_SOFT 0x20 /* soft config */
74#define E_TLB_RAM 0x40 /* extra ram bit */
75
76/* Bits in EPL_790_HWR */
77#define E_790_HWR_SWH 0x80 /* switch register set */
78
79/* Bits in EPL_790_ICR */
80#define E_790_ICR_EIL 0x01 /* enable interrupts */
81
82/* Bits in EPL_790_GCR when E_790_HWR_SWH is set in EPL_790_HWR */
83#define E_790_GCR_IR0 0x04 /* bit 0 of encoded IRQ */
84#define E_790_GCR_IR1 0x08 /* bit 1 of encoded IRQ */
85#define E_790_GCR_IR2 0x40 /* bit 2 of encoded IRQ */
86
87#define inb_we(dep, reg) (inb(dep->de_base_port+reg))
88#define outb_we(dep, reg, data) (outb(dep->de_base_port+reg, data))
89
90#endif /* WDETH_H */
91
92/*
93 * $PchId: wdeth.h,v 1.6 2003/09/10 19:29:52 philip Exp $
94 */
Note: See TracBrowser for help on using the repository browser.