| 1 | /*
|
|---|
| 2 | ibm/rtl8139.h
|
|---|
| 3 |
|
|---|
| 4 | Created: Aug 2003 by Philip Homburg <philip@cs.vu.nl>
|
|---|
| 5 | */
|
|---|
| 6 |
|
|---|
| 7 | #define RL_IDR 0x00 /* Ethernet address
|
|---|
| 8 | * Note: RL_9346CR_EEM_CONFIG mode is
|
|---|
| 9 | * required the change the ethernet
|
|---|
| 10 | * address.
|
|---|
| 11 | * Note: 4-byte write access only.
|
|---|
| 12 | */
|
|---|
| 13 | #define RL_N_TX 4 /* Number of transmit buffers */
|
|---|
| 14 | #define RL_TSD0 0x010 /* Transmit Status of Descriptor 0 */
|
|---|
| 15 | #define RL_TSD_CRS 0x80000000 /* Carrier Sense Lost */
|
|---|
| 16 | #define RL_TSD_TABT 0x40000000 /* Transmit Abort */
|
|---|
| 17 | #define RL_TSD_OWC 0x20000000 /* Out of Window Collision */
|
|---|
| 18 | #define RL_TSD_CDH 0x10000000 /* CD Heart Beat */
|
|---|
| 19 | #define RL_TSD_NCC_M 0x0F000000 /* Number of Collision Count */
|
|---|
| 20 | #define RL_TSD_RES 0x00C00000 /* Reserved */
|
|---|
| 21 | #define RL_TSD_ERTXTH_M 0x003F0000 /* Early Tx Threshold */
|
|---|
| 22 | #define RL_TSD_ERTXTH_S 16 /* shift */
|
|---|
| 23 | #define RL_TSD_ERTXTH_8 0x00000000 /* 8 bytes */
|
|---|
| 24 | #define RL_TSD_TOK 0x00008000 /* Transmit OK */
|
|---|
| 25 | #define RL_TSD_TUN 0x00004000 /* Transmit FIFO Underrun */
|
|---|
| 26 | #define RL_TSD_OWN 0x00002000 /* Controller (does not) Own Buf. */
|
|---|
| 27 | #define RL_TSD_SIZE 0x00001FFF /* Descriptor Size */
|
|---|
| 28 | #define RL_TSAD0 0x20 /* Transmit Start Address of Descriptor 0 */
|
|---|
| 29 | #define RL_RBSTART 0x30 /* Receive Buffer Start Address */
|
|---|
| 30 | #define RL_CR 0x37 /* Command Register */
|
|---|
| 31 | #define RL_CR_RES0 0xE0 /* Reserved */
|
|---|
| 32 | #define RL_CR_RST 0x10 /* Reset */
|
|---|
| 33 | #define RL_CR_RE 0x08 /* Receiver Enable */
|
|---|
| 34 | #define RL_CR_TE 0x04 /* Transmitter Enable *
|
|---|
| 35 | * Note: start with transmit buffer
|
|---|
| 36 | * 0 after RL_CR_TE has been reset.
|
|---|
| 37 | */
|
|---|
| 38 | #define RL_CR_RES1 0x02 /* Reserved */
|
|---|
| 39 | #define RL_CR_BUFE 0x01 /* Receive Buffer Empty */
|
|---|
| 40 | #define RL_CAPR 0x38 /* Current Address of Packet Read */
|
|---|
| 41 | #define RL_CAPR_DATA_OFF 0x10 /* Packet Starts at Offset */
|
|---|
| 42 | #define RL_CBR 0x3A /* Current Buffer Address */
|
|---|
| 43 | #define RL_IMR 0x3C /* Interrupt Mask Register */
|
|---|
| 44 | #define RL_IMR_SERR 0x8000 /* System Error */
|
|---|
| 45 | #define RL_IMR_TIMEOUT 0x4000 /* Time Out */
|
|---|
| 46 | #define RL_IMR_LENCHG 0x2000 /* Cable Length Change */
|
|---|
| 47 | #define RL_IMR_RES 0x1F80 /* Reserved */
|
|---|
| 48 | #define RL_IMR_FOVW 0x0040 /* Rx FIFO Overflow */
|
|---|
| 49 | #define RL_IMR_PUN 0x0020 /* Packet Underrun / Link Change */
|
|---|
| 50 | #define RL_IMR_RXOVW 0x0010 /* Rx Buffer Overflow */
|
|---|
| 51 | #define RL_IMR_TER 0x0008 /* Transmit Error */
|
|---|
| 52 | #define RL_IMR_TOK 0x0004 /* Transmit OK */
|
|---|
| 53 | #define RL_IMR_RER 0x0002 /* Receive Error */
|
|---|
| 54 | #define RL_IMR_ROK 0x0001 /* Receive OK */
|
|---|
| 55 | #define RL_ISR 0x3E /* Interrupt Status Register */
|
|---|
| 56 | #define RL_ISR_SERR 0x8000 /* System Error */
|
|---|
| 57 | #define RL_ISR_TIMEOUT 0x4000 /* Time Out */
|
|---|
| 58 | #define RL_ISR_LENCHG 0x2000 /* Cable Length Change */
|
|---|
| 59 | #define RL_ISR_RES 0x1F80 /* Reserved */
|
|---|
| 60 | #define RL_ISR_FOVW 0x0040 /* Rx FIFO Overflow */
|
|---|
| 61 | #define RL_ISR_PUN 0x0020 /* Packet Underrun / Link Change */
|
|---|
| 62 | #define RL_ISR_RXOVW 0x0010 /* Rx Buffer Overflow */
|
|---|
| 63 | #define RL_ISR_TER 0x0008 /* Transmit Error */
|
|---|
| 64 | #define RL_ISR_TOK 0x0004 /* Transmit OK */
|
|---|
| 65 | #define RL_ISR_RER 0x0002 /* Receive Error */
|
|---|
| 66 | #define RL_ISR_ROK 0x0001 /* Receive OK */
|
|---|
| 67 | #define RL_TCR 0x40 /* Transmit Configuration Register
|
|---|
| 68 | * Note: RL_CR_TE has to be set to
|
|---|
| 69 | * set/change RL_TCR.
|
|---|
| 70 | */
|
|---|
| 71 | #define RL_TCR_RES0 0x80000000 /* Reserved */
|
|---|
| 72 | #define RL_TCR_HWVER_AM 0x7C000000 /* Hardware Version ID A */
|
|---|
| 73 | #define RL_TCR_IFG_M 0x03000000 /* Interframe Gap Time */
|
|---|
| 74 | #define RL_TCR_IFG_STD 0x03000000 /* IEEE 802.3 std */
|
|---|
| 75 | #if 0
|
|---|
| 76 | #undef RL_TCR_IFG_STD
|
|---|
| 77 | #define RL_TCR_IFG_STD 0x00000000
|
|---|
| 78 | #endif
|
|---|
| 79 | #define RL_TCR_HWVER_BM 0x00C00000 /* Hardware Version ID B */
|
|---|
| 80 | #define RL_TCR_HWVER_RTL8139 0x60000000 /* RTL8139 */
|
|---|
| 81 | #define RL_TCR_HWVER_RTL8139A 0x70000000 /* RTL8139A */
|
|---|
| 82 | #define RL_TCR_HWVER_RTL8139AG 0x74000000 /* RTL8139A-G */
|
|---|
| 83 | #define RL_TCR_HWVER_RTL8139B 0x78000000 /* RTL8139B */
|
|---|
| 84 | #define RL_TCR_HWVER_RTL8130 0x78000000 /* RTL8130 (dup) */
|
|---|
| 85 | #define RL_TCR_HWVER_RTL8139C 0x74000000 /* RTL8139C (dup) */
|
|---|
| 86 | #define RL_TCR_HWVER_RTL8100 0x78800000 /* RTL8100 */
|
|---|
| 87 | #define RL_TCR_HWVER_RTL8100B 0x74400000 /* RTL8100B /
|
|---|
| 88 | RTL8139D */
|
|---|
| 89 | #define RL_TCR_HWVER_RTL8139CP 0x74800000 /* RTL8139C+ */
|
|---|
| 90 | #define RL_TCR_HWVER_RTL8101 0x74C00000 /* RTL8101 */
|
|---|
| 91 | #define RL_TCR_RES1 0x00380000 /* Reserved */
|
|---|
| 92 | #define RL_TCR_LBK_M 0x00060000 /* Loopback Test */
|
|---|
| 93 | #define RL_TCR_LBK_NORMAL 0x00000000 /* Normal */
|
|---|
| 94 | #define RL_TCR_LBK_LOOKBOCK 0x00060000 /* Loopback Mode */
|
|---|
| 95 | #define RL_TCR_CRC 0x00010000 /* (Do not) Append CRC */
|
|---|
| 96 | #define RL_TCR_RES2 0x0000F800 /* Reserved */
|
|---|
| 97 | #define RL_TCR_MXDMA_M 0x00000700 /* Max DMA Burst Size Tx */
|
|---|
| 98 | #define RL_TCR_MXDMA_16 0x00000000 /* 16 bytes */
|
|---|
| 99 | #define RL_TCR_MXDMA_32 0x00000100 /* 32 bytes */
|
|---|
| 100 | #define RL_TCR_MXDMA_64 0x00000200 /* 64 bytes */
|
|---|
| 101 | #define RL_TCR_MXDMA_128 0x00000300 /* 128 bytes */
|
|---|
| 102 | #define RL_TCR_MXDMA_128 0x00000300 /* 128 bytes */
|
|---|
| 103 | #define RL_TCR_MXDMA_256 0x00000400 /* 256 bytes */
|
|---|
| 104 | #define RL_TCR_MXDMA_512 0x00000500 /* 512 bytes */
|
|---|
| 105 | #define RL_TCR_MXDMA_1024 0x00000600 /* 1024 bytes */
|
|---|
| 106 | #define RL_TCR_MXDMA_2048 0x00000700 /* 2048 bytes */
|
|---|
| 107 | #define RL_TCR_TXRR_M 0x000000F0 /* Tx Retry Count */
|
|---|
| 108 | #define RL_TCR_RES3 0x0000000E /* Reserved */
|
|---|
| 109 | #define RL_TCR_CLRABT 0x00000001 /* Clear Abort */
|
|---|
| 110 | #define RL_RCR 0x44 /* Receive Configuration Register
|
|---|
| 111 | * Note: RL_CR_RE has to be set to
|
|---|
| 112 | * set/change RL_RCR.
|
|---|
| 113 | */
|
|---|
| 114 | #define RL_RCR_RES0 0xF0000000 /& Reserved */
|
|---|
| 115 | #define RL_RCR_ERTH_M 0x0F000000 /* Early Rx Threshold */
|
|---|
| 116 | #define RL_RCR_ERTH_0 0x00000000 /* No threshold */
|
|---|
| 117 | #define RL_RCR_ERTH_1 0x01000000 /* 1/16 */
|
|---|
| 118 | #define RL_RCR_ERTH_2 0x02000000 /* 2/16 */
|
|---|
| 119 | #define RL_RCR_ERTH_3 0x03000000 /* 3/16 */
|
|---|
| 120 | #define RL_RCR_ERTH_4 0x04000000 /* 4/16 */
|
|---|
| 121 | #define RL_RCR_ERTH_5 0x05000000 /* 5/16 */
|
|---|
| 122 | #define RL_RCR_ERTH_6 0x06000000 /* 6/16 */
|
|---|
| 123 | #define RL_RCR_ERTH_7 0x07000000 /* 7/16 */
|
|---|
| 124 | #define RL_RCR_ERTH_8 0x08000000 /* 8/16 */
|
|---|
| 125 | #define RL_RCR_ERTH_9 0x09000000 /* 9/16 */
|
|---|
| 126 | #define RL_RCR_ERTH_10 0x0A000000 /* 10/16 */
|
|---|
| 127 | #define RL_RCR_ERTH_11 0x0B000000 /* 11/16 */
|
|---|
| 128 | #define RL_RCR_ERTH_12 0x0C000000 /* 12/16 */
|
|---|
| 129 | #define RL_RCR_ERTH_13 0x0D000000 /* 13/16 */
|
|---|
| 130 | #define RL_RCR_ERTH_14 0x0E000000 /* 14/16 */
|
|---|
| 131 | #define RL_RCR_ERTH_15 0x0F000000 /* 15/16 */
|
|---|
| 132 | #define RL_RCR_RES1 0x00FC0000 /* Reserved */
|
|---|
| 133 | #define RL_RCR_MULERINT 0x00020000 /* Multiple Early Int Select */
|
|---|
| 134 | #define RL_RCR_RER8 0x00010000 /* Receive small error packet */
|
|---|
| 135 | #define RL_RCR_RXFTH_M 0x0000E000 /* Rx FIFO Threshold */
|
|---|
| 136 | #define RL_RCR_RXFTH_16 0x00000000 /* 16 bytes */
|
|---|
| 137 | #define RL_RCR_RXFTH_32 0x00002000 /* 32 bytes */
|
|---|
| 138 | #define RL_RCR_RXFTH_64 0x00004000 /* 64 bytes */
|
|---|
| 139 | #define RL_RCR_RXFTH_128 0x00006000 /* 128 bytes */
|
|---|
| 140 | #define RL_RCR_RXFTH_256 0x00008000 /* 256 bytes */
|
|---|
| 141 | #define RL_RCR_RXFTH_512 0x0000A000 /* 512 bytes */
|
|---|
| 142 | #define RL_RCR_RXFTH_1024 0x0000C000 /* 1024 bytes */
|
|---|
| 143 | #define RL_RCR_RXFTH_UNLIM 0x0000E000 /* unlimited */
|
|---|
| 144 | #define RL_RCR_RBLEM_M 0x00001800 /* Rx Buffer Length */
|
|---|
| 145 | #define RL_RCR_RBLEN_8K 0x00000000 /* 8KB + 16 bytes */
|
|---|
| 146 | #define RL_RCR_RBLEN_8K_SIZE (8*1024)
|
|---|
| 147 | #define RL_RCR_RBLEN_16K 0x00000800 /* 16KB + 16 bytes */
|
|---|
| 148 | #define RL_RCR_RBLEN_16K_SIZE (16*1024)
|
|---|
| 149 | #define RL_RCR_RBLEN_32K 0x00001000 /* 32KB + 16 bytes */
|
|---|
| 150 | #define RL_RCR_RBLEN_32K_SIZE (32*1024)
|
|---|
| 151 | #define RL_RCR_RBLEN_64K 0x00001800 /* 64KB + 16 bytes */
|
|---|
| 152 | #define RL_RCR_RBLEN_64K_SIZE (64*1024)
|
|---|
| 153 | /* Note: the documentation for the RTL8139C(L) or
|
|---|
| 154 | * for the RTL8139D(L) claims that the buffer should
|
|---|
| 155 | * be 16 bytes larger. Multiples of 8KB are the
|
|---|
| 156 | * correct values.
|
|---|
| 157 | */
|
|---|
| 158 | #define RL_RCR_MXDMA_M 0x00000700 /* Rx DMA burst size */
|
|---|
| 159 | #define RL_RCR_MXDMA_16 0x00000000 /* 16 bytes */
|
|---|
| 160 | #define RL_RCR_MXDMA_32 0x00000100 /* 32 bytes */
|
|---|
| 161 | #define RL_RCR_MXDMA_64 0x00000200 /* 64 bytes */
|
|---|
| 162 | #define RL_RCR_MXDMA_128 0x00000300 /* 128 bytes */
|
|---|
| 163 | #define RL_RCR_MXDMA_256 0x00000400 /* 256 bytes */
|
|---|
| 164 | #define RL_RCR_MXDMA_512 0x00000500 /* 512 bytes */
|
|---|
| 165 | #define RL_RCR_MXDMA_1024 0x00000600 /* 1024 bytes */
|
|---|
| 166 | #define RL_RCR_MXDMA_UNLIM 0x00000700 /* unlimited */
|
|---|
| 167 | #define RL_RCR_WRAP 0x00000080 /* (Do not) Wrap on receive */
|
|---|
| 168 | #define RL_RCR_RES2 0x00000040 /* EEPROM type? */
|
|---|
| 169 | #define RL_RCR_AER 0x00000020 /* Accept Error Packets */
|
|---|
| 170 | #define RL_RCR_AR 0x00000010 /* Accept Runt Packets */
|
|---|
| 171 | #define RL_RCR_AB 0x00000008 /* Accept Broadcast Packets */
|
|---|
| 172 | #define RL_RCR_AM 0x00000004 /* Accept Multicast Packets */
|
|---|
| 173 | #define RL_RCR_APM 0x00000002 /* Accept Physical Match Packets */
|
|---|
| 174 | #define RL_RCR_AAP 0x00000001 /* Accept All Packets */
|
|---|
| 175 | #define RL_MPC 0x4c /* Missed Packet Counter */
|
|---|
| 176 | #define RL_9346CR 0x50 /* 93C46 Command Register */
|
|---|
| 177 | #define RL_9346CR_EEM_M 0xC0 /* Operating Mode */
|
|---|
| 178 | #define RL_9346CR_EEM_NORMAL 0x00 /* Normal Mode */
|
|---|
| 179 | #define RL_9346CR_EEM_AUTOLOAD 0x40 /* Load from 93C46 */
|
|---|
| 180 | #define RL_9346CR_EEM_PROG 0x80 /* 93C46 Programming */
|
|---|
| 181 | #define RL_9346CR_EEM_CONFIG 0xC0 /* Config Write Enable */
|
|---|
| 182 | #define RL_9346CR_RES 0x30 /* Reserved */
|
|---|
| 183 | #define RL_9346CR_EECS 0x08 /* EECS Pin */
|
|---|
| 184 | #define RL_9346CR_EESK 0x04 /* EESK Pin */
|
|---|
| 185 | #define RL_9346CR_EEDI 0x02 /* EEDI Pin */
|
|---|
| 186 | #define RL_9346CR_EEDO 0x01 /* EEDO Pin */
|
|---|
| 187 | #define RL_CONFIG0 0x51 /* Configuration Register 0 */
|
|---|
| 188 | #define RL_CONFIG1 0x52 /* Configuration Register 1 */
|
|---|
| 189 | #define RL_MSR 0x58 /* Media Status Register */
|
|---|
| 190 | #define RL_MSR_TXFCE 0x80 /* Tx Flow Control Enable */
|
|---|
| 191 | #define RL_MSR_RXFCE 0x40 /* Rx Flow Control Enable */
|
|---|
| 192 | #define RL_MSR_RES 0x20 /* Reserved */
|
|---|
| 193 | #define RL_MSR_AUXSTAT 0x10 /* Aux. Power Present */
|
|---|
| 194 | #define RL_MSR_SPEED_10 0x08 /* In 10 Mbps mode */
|
|---|
| 195 | #define RL_MSR_LINKB 0x04 /* link Failed */
|
|---|
| 196 | #define RL_MSR_TXPF 0x02 /* Sent Pause Packet */
|
|---|
| 197 | #define RL_MSR_RXPF 0x01 /* Received Pause Packet */
|
|---|
| 198 | #define RL_CONFIG3 0x59 /* Configuration Register 3 */
|
|---|
| 199 | #define RL_CONFIG4 0x5A /* Configuration Register 4 */
|
|---|
| 200 | /* 0x5B */ /* Reserved */
|
|---|
| 201 | #define RL_REVID 0x5E /* PCI Revision ID */
|
|---|
| 202 | /* 0x5F */ /* Reserved */
|
|---|
| 203 | #define RL_TSAD 0x60 /* Transmit Status of All Descriptors */
|
|---|
| 204 | #define RL_TSAD_TOK3 0x8000 /* TOK bit of Descriptor 3 */
|
|---|
| 205 | #define RL_TSAD_TOK2 0x4000 /* TOK bit of Descriptor 2 */
|
|---|
| 206 | #define RL_TSAD_TOK1 0x2000 /* TOK bit of Descriptor 1 */
|
|---|
| 207 | #define RL_TSAD_TOK0 0x1000 /* TOK bit of Descriptor 0 */
|
|---|
| 208 | #define RL_TSAD_TUN3 0x0800 /* TUN bit of Descriptor 3 */
|
|---|
| 209 | #define RL_TSAD_TUN2 0x0400 /* TUN bit of Descriptor 2 */
|
|---|
| 210 | #define RL_TSAD_TUN1 0x0200 /* TUN bit of Descriptor 1 */
|
|---|
| 211 | #define RL_TSAD_TUN0 0x0100 /* TUN bit of Descriptor 0 */
|
|---|
| 212 | #define RL_TSAD_TABT3 0x0080 /* TABT bit of Descriptor 3 */
|
|---|
| 213 | #define RL_TSAD_TABT2 0x0040 /* TABT bit of Descriptor 2 */
|
|---|
| 214 | #define RL_TSAD_TABT1 0x0020 /* TABT bit of Descriptor 1 */
|
|---|
| 215 | #define RL_TSAD_TABT0 0x0010 /* TABT bit of Descriptor 0 */
|
|---|
| 216 | #define RL_TSAD_OWN3 0x0008 /* OWN bit of Descriptor 3 */
|
|---|
| 217 | #define RL_TSAD_OWN2 0x0004 /* OWN bit of Descriptor 2 */
|
|---|
| 218 | #define RL_TSAD_OWN1 0x0002 /* OWN bit of Descriptor 1 */
|
|---|
| 219 | #define RL_TSAD_OWN0 0x0001 /* OWN bit of Descriptor 0 */
|
|---|
| 220 | #define RL_BMCR 0x62 /* Basic Mode Control Register (MII_CTRL) */
|
|---|
| 221 | #define RL_BMSR 0x64 /* Basic Mode Status Register (MII_STATUS) */
|
|---|
| 222 | #define RL_ANAR 0x66 /* Auto-Neg Advertisement Register (MII_ANA) */
|
|---|
| 223 | #define RL_ANLPAR 0x68 /* Auto-Neg Link Partner Register (MII_ANLPA) */
|
|---|
| 224 | #define RL_ANER 0x6a /* Auto-Neg Expansion Register (MII_ANE) */
|
|---|
| 225 | #define RL_NWAYTR 0x70 /* N-way Test Register */
|
|---|
| 226 | #define RL_CSCR 0x74 /* CS Configuration Register */
|
|---|
| 227 | #define RL_CONFIG5 0xD8 /* Configuration Register 5 */
|
|---|
| 228 |
|
|---|
| 229 | /* Status word in receive buffer */
|
|---|
| 230 | #define RL_RXS_LEN_M 0xFFFF0000 /* Length Field, Excl. Status word */
|
|---|
| 231 | #define RL_RXS_LEN_S 16 /* Shift For Length */
|
|---|
| 232 | #define RL_RXS_MAR 0x00008000 /* Multicast Address Received */
|
|---|
| 233 | #define RL_RXS_PAR 0x00004000 /* Physical Address Matched */
|
|---|
| 234 | #define RL_RXS_BAR 0x00002000 /* Broadcast Address Received */
|
|---|
| 235 | #define RL_RXS_RES_M 0x00001FC0 /* Reserved */
|
|---|
| 236 | #define RL_RXS_ISE 0x00000020 /* Invalid Symbol Error */
|
|---|
| 237 | #define RL_RXS_RUNT 0x00000010 /* Runt Packet Received */
|
|---|
| 238 | #define RL_RXS_LONG 0x00000008 /* Long (>4KB) Packet */
|
|---|
| 239 | #define RL_RXS_CRC 0x00000004 /* CRC Error */
|
|---|
| 240 | #define RL_RXS_FAE 0x00000002 /* Frame Alignment Error */
|
|---|
| 241 | #define RL_RXS_ROK 0x00000001 /* Receive OK */
|
|---|
| 242 |
|
|---|
| 243 | /* Registers in the Machine Independent Interface (MII) to the PHY.
|
|---|
| 244 | * IEEE 802.3 (2000 Edition) Clause 22.
|
|---|
| 245 | */
|
|---|
| 246 | #define MII_CTRL 0x0 /* Control Register (basic) */
|
|---|
| 247 | #define MII_CTRL_RST 0x8000 /* Reset PHY */
|
|---|
| 248 | #define MII_CTRL_LB 0x4000 /* Enable Loopback Mode */
|
|---|
| 249 | #define MII_CTRL_SP_LSB 0x2000 /* Speed Selection (LSB) */
|
|---|
| 250 | #define MII_CTRL_ANE 0x1000 /* Auto Negotiation Enable */
|
|---|
| 251 | #define MII_CTRL_PD 0x0800 /* Power Down */
|
|---|
| 252 | #define MII_CTRL_ISO 0x0400 /* Isolate */
|
|---|
| 253 | #define MII_CTRL_RAN 0x0200 /* Restart Auto-Negotiation Process */
|
|---|
| 254 | #define MII_CTRL_DM 0x0100 /* Full Duplex */
|
|---|
| 255 | #define MII_CTRL_CT 0x0080 /* Enable COL Signal Test */
|
|---|
| 256 | #define MII_CTRL_SP_MSB 0x0040 /* Speed Selection (MSB) */
|
|---|
| 257 | #define MII_CTRL_SP_10 0x0000 /* 10 Mb/s */
|
|---|
| 258 | #define MII_CTRL_SP_100 0x2000 /* 100 Mb/s */
|
|---|
| 259 | #define MII_CTRL_SP_1000 0x0040 /* 1000 Mb/s */
|
|---|
| 260 | #define MII_CTRL_SP_RES 0x2040 /* Reserved */
|
|---|
| 261 | #define MII_CTRL_RES 0x003F /* Reserved */
|
|---|
| 262 | #define MII_STATUS 0x1 /* Status Register (basic) */
|
|---|
| 263 | #define MII_STATUS_100T4 0x8000 /* 100Base-T4 support */
|
|---|
| 264 | #define MII_STATUS_100XFD 0x4000 /* 100Base-X FD support */
|
|---|
| 265 | #define MII_STATUS_100XHD 0x2000 /* 100Base-X HD support */
|
|---|
| 266 | #define MII_STATUS_10FD 0x1000 /* 10 Mb/s FD support */
|
|---|
| 267 | #define MII_STATUS_10HD 0x0800 /* 10 Mb/s HD support */
|
|---|
| 268 | #define MII_STATUS_100T2FD 0x0400 /* 100Base-T2 FD support */
|
|---|
| 269 | #define MII_STATUS_100T2HD 0x0200 /* 100Base-T2 HD support */
|
|---|
| 270 | #define MII_STATUS_EXT_STAT 0x0100 /* Supports MII_EXT_STATUS */
|
|---|
| 271 | #define MII_STATUS_RES 0x0080 /* Reserved */
|
|---|
| 272 | #define MII_STATUS_MFPS 0x0040 /* MF Preamble Suppression */
|
|---|
| 273 | #define MII_STATUS_ANC 0x0020 /* Auto-Negotiation Completed */
|
|---|
| 274 | #define MII_STATUS_RF 0x0010 /* Remote Fault Detected */
|
|---|
| 275 | #define MII_STATUS_ANA 0x0008 /* Auto-Negotiation Ability */
|
|---|
| 276 | #define MII_STATUS_LS 0x0004 /* Link Up */
|
|---|
| 277 | #define MII_STATUS_JD 0x0002 /* Jabber Condition Detected */
|
|---|
| 278 | #define MII_STATUS_EC 0x0001 /* Ext Register Capabilities */
|
|---|
| 279 | #define MII_PHYID_H 0x2 /* PHY ID (high) */
|
|---|
| 280 | #define MII_PHYID_L 0x3 /* PHY ID (low) */
|
|---|
| 281 | #define MII_ANA 0x4 /* Auto-Negotiation Advertisement */
|
|---|
| 282 | #define MII_ANA_NP 0x8000 /* Next PAge */
|
|---|
| 283 | #define MII_ANA_RES 0x4000 /* Reserved */
|
|---|
| 284 | #define MII_ANA_RF 0x2000 /* Remote Fault */
|
|---|
| 285 | #define MII_ANA_TAF_M 0x1FE0 /* Technology Ability Field */
|
|---|
| 286 | #define MII_ANA_TAF_S 5 /* Shift */
|
|---|
| 287 | #define MII_ANA_TAF_RES 0x1000 /* Reserved */
|
|---|
| 288 | #define MII_ANA_PAUSE_ASYM 0x0800 /* Asym. Pause */
|
|---|
| 289 | #define MII_ANA_PAUSE_SYM 0x0400 /* Sym. Pause */
|
|---|
| 290 | #define MII_ANA_100T4 0x0200 /* 100Base-T4 */
|
|---|
| 291 | #define MII_ANA_100TXFD 0x0100 /* 100Base-TX FD */
|
|---|
| 292 | #define MII_ANA_100TXHD 0x0080 /* 100Base-TX HD */
|
|---|
| 293 | #define MII_ANA_10TFD 0x0040 /* 10Base-T FD */
|
|---|
| 294 | #define MII_ANA_10THD 0x0020 /* 10Base-T HD */
|
|---|
| 295 | #define MII_ANA_SEL_M 0x001F /* Selector Field */
|
|---|
| 296 | #define MII_ANA_SEL_802_3 0x0001 /* 802.3 */
|
|---|
| 297 | #define MII_ANLPA 0x5 /* Auto-Neg Link Partner Ability Register */
|
|---|
| 298 | #define MII_ANLPA_NP 0x8000 /* Next Page */
|
|---|
| 299 | #define MII_ANLPA_ACK 0x4000 /* Acknowledge */
|
|---|
| 300 | #define MII_ANLPA_RF 0x2000 /* Remote Fault */
|
|---|
| 301 | #define MII_ANLPA_TAF_M 0x1FC0 /* Technology Ability Field */
|
|---|
| 302 | #define MII_ANLPA_SEL_M 0x001F /* Selector Field */
|
|---|
| 303 | #define MII_ANE 0x6 /* Auto-Negotiation Expansion */
|
|---|
| 304 | #define MII_ANE_RES 0xFFE0 /* Reserved */
|
|---|
| 305 | #define MII_ANE_PDF 0x0010 /* Parallel Detection Fault */
|
|---|
| 306 | #define MII_ANE_LPNPA 0x0008 /* Link Partner is Next Page Able */
|
|---|
| 307 | #define MII_ANE_NPA 0x0002 /* Local Device is Next Page Able */
|
|---|
| 308 | #define MII_ANE_PR 0x0002 /* New Page has been received */
|
|---|
| 309 | #define MII_ANE_LPANA 0x0001 /* Link Partner is Auto-Neg.able */
|
|---|
| 310 | #define MII_ANNPT 0x7 /* Auto-Negotiation Next Page Transmit */
|
|---|
| 311 | #define MII_ANLPRNP 0x8 /* Auto-Neg Link Partner Received Next Page */
|
|---|
| 312 | #define MII_MS_CTRL 0x9 /* MASTER-SLAVE Control Register */
|
|---|
| 313 | #define MII_MS_STATUS 0xA /* MASTER-SLAVE Status Register */
|
|---|
| 314 | /* 0xB ... 0xE */ /* Reserved */
|
|---|
| 315 | #define MII_EXT_STATUS 0xF /* Extended Status */
|
|---|
| 316 | #define MII_ESTAT_1000XFD 0x8000 /* 1000Base-X Full Duplex */
|
|---|
| 317 | #define MII_ESTAT_1000XHD 0x4000 /* 1000Base-X Half Duplex */
|
|---|
| 318 | #define MII_ESTAT_1000TFD 0x2000 /* 1000Base-T Full Duplex */
|
|---|
| 319 | #define MII_ESTAT_1000THD 0x1000 /* 1000Base-T Half Duplex */
|
|---|
| 320 | #define MII_ESTAT_RES 0x0FFF /* Reserved */
|
|---|
| 321 | /* 0x10 ... 0x1F */ /* Vendor Specific */
|
|---|
| 322 |
|
|---|
| 323 | #if 0
|
|---|
| 324 | 34-35 R ERBCR Early Receive (Rx) Byte Count Register
|
|---|
| 325 | 36 R ERSR Early Rx Status Register
|
|---|
| 326 | 7-4 reserved
|
|---|
| 327 | 3 R ERGood Early Rx Good packet
|
|---|
| 328 | 2 R ERBad Early Rx Bad packet
|
|---|
| 329 | 1 R EROVW Early Rx OverWrite
|
|---|
| 330 | 0 R EROK Early Rx OK
|
|---|
| 331 | 51 R/W CONFIG0 Configuration Register 0
|
|---|
| 332 | 7 R SCR Scrambler Mode
|
|---|
| 333 | 6 R PCS PCS Mode
|
|---|
| 334 | 5 R T10 10 Mbps Mode
|
|---|
| 335 | 4-3 R PL[1-0] Select 10 Mbps medium type
|
|---|
| 336 | 2-0 R BS[2-0] Select Boot ROM size
|
|---|
| 337 | 52 R/W CONFIG1 Configuration Register 1
|
|---|
| 338 | 7-6 R/W LEDS[1-0] LED PIN
|
|---|
| 339 | 5 R/W DVRLOAD Driver Load
|
|---|
| 340 | 4 R/W LWACT LWAKE active mode
|
|---|
| 341 | 3 R MEMMAP Memory Mapping
|
|---|
| 342 | 2 R IOMAP I/O Mapping
|
|---|
| 343 | 1 R/W VPD Set to enable Vital Product Data
|
|---|
| 344 | 0 R/W PMEn Power Management Enable
|
|---|
| 345 | 59 R/W CONFIG3 Configuration Register 3
|
|---|
| 346 | 7 R GNTSel Gnt Select
|
|---|
| 347 | 6 R/W PARM_En Parameter Enable
|
|---|
| 348 | 5 R/W Magic Magic Packet
|
|---|
| 349 | 4 R/W LinkUp Link Up
|
|---|
| 350 | 3 reserved
|
|---|
| 351 | 2 R CLKRUN_En CLKRUN Enable
|
|---|
| 352 | 1 reserved
|
|---|
| 353 | 0 R FBtBEn Fast Back to Back Enable
|
|---|
| 354 | 5a R/W CONFIG4 Configuration Register 4
|
|---|
| 355 | 7 R/W RxFIFOAutoClr Auto Clear the Rx FIFO on overflow
|
|---|
| 356 | 6 R/W AnaOff Analog Power Off
|
|---|
| 357 | 5 R/W LongWF Long Wake-up Frame
|
|---|
| 358 | 4 R/W LWPME LANWAKE vs PMEB
|
|---|
| 359 | 3 reserved
|
|---|
| 360 | 2 R/W LWPTN LWAKE pattern
|
|---|
| 361 | 1 reserved
|
|---|
| 362 | 0 R/W PBWakeup Pre-Boot Wakeup
|
|---|
| 363 | 5c-5d R/W MULINT Multiple Interrupt Select
|
|---|
| 364 | 15-12 reserved
|
|---|
| 365 | 11-0 R/W MISR[11-0] Multiple Interrupt Select
|
|---|
| 366 | 68-69 R ANLPAR Auto-Negotiation Link Partnet Register
|
|---|
| 367 | 15 R NP Next Page bit
|
|---|
| 368 | 14 R ACK acknowledge received from link partner
|
|---|
| 369 | 13 R/W RF received remote fault detection capability
|
|---|
| 370 | 12-11 reserved
|
|---|
| 371 | 10 R Pause Flow control is supported
|
|---|
| 372 | 9 R T4 100Base-T4 is supported
|
|---|
| 373 | 8 R/W TXFD 100Base-TX full duplex is supported
|
|---|
| 374 | 7 R/W TX 100Base-TX is supported
|
|---|
| 375 | 6 R/W 10FD 10Base-T full duplex is supported
|
|---|
| 376 | 5 R/W 10 10Base-T is supported
|
|---|
| 377 | 4-0 R/W Selector Binary encoded selector
|
|---|
| 378 | 6a-6b R ANER Auto-Negotiation Expansion Register
|
|---|
| 379 | 15-5 reserved
|
|---|
| 380 | 4 R MLF Multiple link fault occured
|
|---|
| 381 | 3 R LP_NP_ABLE Link partner supports Next Page
|
|---|
| 382 | 2 R NP_ABLE Local node is able to send add. Next Pages
|
|---|
| 383 | 1 R PAGE_RX Link Code Word Page received
|
|---|
| 384 | 0 R LP_NW_ABLE Link partner supports NWay auto-negotiation
|
|---|
| 385 | 70-71 R/W NWAYTR N-way Test Register
|
|---|
| 386 | 15-8 reserved
|
|---|
| 387 | 7 R/W NWLPBK NWay loopback mode
|
|---|
| 388 | 6-4 reserved
|
|---|
| 389 | 3 R ENNWLE LED0 pin indicates linkpulse
|
|---|
| 390 | 2 R FLAGABD Auto-neg experienced ability detect state
|
|---|
| 391 | 1 R FLAGPDF Auto-neg exp. par. detection fault state
|
|---|
| 392 | 0 R FLAGLSC Auto-neg experienced link status check state
|
|---|
| 393 | 74-75 R/W CSCR CS Configuration Register
|
|---|
| 394 | 15 W Testfun Auto-neg speeds up internal timer
|
|---|
| 395 | 14-10 reserved
|
|---|
| 396 | 9 R/W LD Active low TPI link disable signal
|
|---|
| 397 | 8 R/W HEARTBEAT HEART BEAT enable
|
|---|
| 398 | 7 R/W JBEN Enable jabber function
|
|---|
| 399 | 6 R/W F_LINK_100 Force 100 Mbps
|
|---|
| 400 | 5 R/W F_Conect Bypass disconnect function
|
|---|
| 401 | 4 reserved
|
|---|
| 402 | 3 R Con_status Connected link detected
|
|---|
| 403 | 2 R/W Con_status_En Configures LED1 to indicate conn. stat.
|
|---|
| 404 | 1 reserved
|
|---|
| 405 | 0 R/W PASS_SCR Bypass scramble
|
|---|
| 406 | 76-77 reserved
|
|---|
| 407 | 78-7b R/W PHY1_PARM PHY parameter 1
|
|---|
| 408 | 7c-7f R/W TW_PARM Twister parameter
|
|---|
| 409 | 80 R/W PHY2_PARM PHY parameter 2
|
|---|
| 410 | 81-83 reserved
|
|---|
| 411 | 84-8b R/W CRC[0-7] Power Management CRC reg.[0-7] for frame[0-7]
|
|---|
| 412 | 8c-cb R/W Wakeup[0-7] Power Management wakeup frame[0-7] (64 bit)
|
|---|
| 413 | cc-d3 R/W LSBCRC[0-7] LSB of the mask byte of makeup frame[0-7]
|
|---|
| 414 | d4-d7 reserved
|
|---|
| 415 | d8 R/W Config5 Configuration register 5
|
|---|
| 416 | 7 reserved
|
|---|
| 417 | 6 R/W BWF Broadcast Wakeup Frame
|
|---|
| 418 | 5 R/W MWF Multicast Wakeup Frame
|
|---|
| 419 | 4 R/W UWF Unicast Wakeup Frame
|
|---|
| 420 | 3 R/W FifoAddrPtr FIFO Address Pointer
|
|---|
| 421 | 2 R/W LDPS Link Down Power Saving mode
|
|---|
| 422 | 1 R/W LANWake LANWake Signal
|
|---|
| 423 | 0 R/W PME_STS PME_Status bit
|
|---|
| 424 | d9-ff reserved
|
|---|
| 425 | #endif
|
|---|
| 426 |
|
|---|
| 427 | /*
|
|---|
| 428 | * $PchId: rtl8139.h,v 1.1 2003/09/05 10:58:50 philip Exp $
|
|---|
| 429 | */
|
|---|
